cst tight crop
  • Safety Courses
  • Course Directory
  • Online Courses
  • About Us
  • Contact Us
  • News
✕
  • Safety Courses
  • Course Directory
  • Online Courses
  • About Us
  • Contact Us
  • News
Email
Phone
✕
Search
Course Calendar
  • Home
  • Training and Courses Directory
  • Uncategorized
  • How to Select Gas Monitors for Your Worksite
How to Select Gas Monitors for Your Worksite

A gas monitor that detects the wrong hazard is not a control. It can give a crew false confidence at the exact point they need reliable information. Knowing how to select gas monitors starts with the job, the atmosphere that may be present and what workers need to do when an alarm sounds – not with the cheapest unit on a catalogue page.

For construction, maintenance, utilities, industrial cleaning and confined-space work, monitor selection needs to be part of the risk assessment and permit process. The equipment must suit the hazards, work method, environmental conditions and the competence of the person using it.

Start with the atmosphere you may encounter

Before choosing a monitor, identify the gases and vapours that could reasonably be present. Consider the work area, nearby processes, stored substances, residue in tanks or pipes, work being performed and whether the atmosphere can change during the task.

A confined space may contain low oxygen because of rusting, decomposition, displacement by another gas or poor ventilation. It may contain flammable vapours from fuels, solvents or cleaning products. It may also contain toxic contaminants such as carbon monoxide, hydrogen sulphide, sulphur dioxide, ammonia or chlorine, depending on the site and process.

Do not assume a standard four-gas monitor covers every job. A typical four-gas unit measures oxygen, flammable gas as a percentage of the lower explosive limit (LEL), carbon monoxide and hydrogen sulphide. That combination is suitable for many confined-space and general industrial applications, but it will not identify every toxic gas or vapour.

If workers are entering a sewer, treating wastewater, cleaning chemical tanks, welding in an enclosed area or working around refrigeration plant, the likely contaminants may require different sensors. Obtain current safety data sheets, speak with the asset owner and review previous incident, exposure and atmospheric-testing information. If the hazard is unclear, stop and get competent advice before relying on a monitor.

Select gas monitors by job, not by habit

The monitor format must match how and where testing occurs. The right instrument for a worker walking through an open plant area may not be right for testing a vessel before entry.

Personal diffusion monitors

A diffusion monitor relies on the surrounding air reaching the sensors naturally. These are commonly worn in the breathing zone and are useful for ongoing personal monitoring where workers are moving through an area.

They are not a substitute for remote testing of a confined space before entry. A worker must not place their head or body into an opening simply to determine whether the air is safe. If pre-entry sampling is required, a pumped instrument with a suitable sampling line is generally the practical choice.

Pumped gas monitors

A pumped monitor draws air through a hose from a remote point. This allows testing from outside a pit, tank, vessel, manhole or enclosed area, and enables sampling at different levels before entry.

Allow enough time for the sample to travel through the line and reach the sensors. The required time depends on hose length, pump flow and manufacturer instructions. Rushing this step can produce a reading that reflects the air near the instrument rather than the atmosphere at the sampling point.

Single-gas and multi-gas monitors

A single-gas monitor can be appropriate when one known hazard is the concern, such as personal carbon monoxide monitoring near combustion sources. For changing work conditions or confined spaces, a multi-gas monitor may be more suitable because oxygen, flammability and toxic contaminants can interact or develop together.

More sensors are not automatically better. Extra sensors increase cost, servicing requirements and the chance that users misunderstand readings. Select the sensors required by the documented hazards, then make sure the people using the monitor understand what each channel does and does not detect.

Check sensor limitations before you buy

Every gas sensor has limits. Those limits should be understood by the supervisor, permit issuer and gas tester before the monitor is placed into service.

Catalytic sensors used for flammable-gas detection can be affected by silicone vapours, lead compounds and other contaminants. Some atmospheres may be oxygen deficient, which can affect the reliability of certain flammable-gas readings. Infrared LEL sensors can offer advantages in some applications, including environments where sensor poisoning is a concern, but they also have limitations and may not respond to every gas in the same way.

Electrochemical toxic-gas sensors can respond to more than one gas. This is known as cross-sensitivity. A monitor may show a response, but the reading may not mean what the operator assumes it means. Check the manufacturer’s technical information for the target gas, measurement range, cross-sensitivities, operating temperature and humidity limits.

Also consider whether the monitor is approved or suitable for the classified hazardous area where it will be used. A gas monitor itself must not introduce an ignition source into a flammable atmosphere.

Set alarms that trigger action

An alarm only helps if the response is clear. Select a monitor with audible, visual and vibrating alarms that can be recognised in the actual work environment. A loud worksite, hearing protection, poor lighting and workers in bulky PPE can all reduce the chance of an alarm being noticed.

Alarm set points must be established through the site’s procedures, risk assessment, exposure requirements and manufacturer guidance. Workers need to know the immediate action for each alarm. In many situations, that means stop work, leave the area or do not enter, warn others and report to the responsible person. It does not mean attempting to investigate an unknown atmosphere without the correct controls and rescue arrangements.

For confined-space entry, monitoring is not a one-off test at the opening. Atmospheric conditions can change after ventilation starts, when a product is disturbed, when welding begins or when other work occurs nearby. The monitoring plan should state who tests, where they test, how often testing is repeated and how readings are recorded on the permit.

Plan for stratification and changing conditions

Gases do not always mix evenly. Some may collect at low points, while others rise or remain suspended depending on their properties, temperature, ventilation and the shape of the space. Deep pits, tanks, trenches and poorly ventilated voids can contain different atmospheres at different heights.

Use a remote sampling method where required and test the relevant levels of the space before entry. Continue monitoring during the work where the risk assessment requires it. A safe reading at the top of a vessel does not prove the bottom is safe, and a safe reading at the start of a shift does not guarantee conditions later in the job.

Ventilation can be an effective control, but it needs to be selected and managed properly. It may dilute contaminants, or it may move them to another location. It should never be used as an excuse to skip testing.

Budget for the full life of the monitor

The purchase price is only one part of the decision. A monitor needs bump testing, calibration, charging or battery replacement, sensor replacement, cleaning, records and repair support. If those tasks are not planned and funded, the monitor will eventually become an unreliable item in the store room.

A bump test checks that the sensors respond to a known test gas and that alarms operate. Calibration adjusts the instrument against a known standard. They are not interchangeable. Follow the manufacturer’s requirements and site procedures for both, including the frequency of testing and the action to take when a monitor fails.

Consider practical matters as well. Can your team obtain calibration gas and replacement parts? Is the monitor easy to operate while wearing gloves? Does it provide event logs or data download if your permit system needs records? Is there local servicing support, or will the unit be away for weeks when you need it most?

Train the people who will rely on it

A quality instrument cannot compensate for an untrained user. Workers need practical instruction in pre-use checks, bump testing, calibration status, sample-line testing, alarm response, sensor limitations and recordkeeping. Supervisors need to know when a reading requires work to stop and when specialist advice is needed.

For crews performing confined-space gas testing, the relevant competency is often MSMWHS217 Gas test atmospheres. Combined Safety Training delivers training and assessment on behalf of Allens Training Pty Ltd, RTO 90909, with practical delivery that can be contextualised to the gases, permits and equipment used at your workplace.

Choose the monitor after you understand the hazard, then maintain it and train people to use it properly. If the atmosphere can harm, overcome or ignite, the right decision is the one that gives workers a clear warning early enough to get out safely.

combined safety training logo
ACN 651 497 399 | ABN 77 651 497 399
108 Albatross Road, South Nowra NSW 2541
0413589467 | training@combinedsafetytraining.com.au

Training and assessment delivered on behalf of
Allens Training Pty Ltd RTO 90909
  • All Training and Courses
  • About Us
  • Contact Us
training and assessment delivered on behalf of allens training rto 90909
  • Privacy Policy
  • Course Refund Policy
  • Student Handbook
  • Upcoming Course Calendar
© 2025 Combined Safety Training Pty Ltd | | All Rights Reserved
Safety Training, Nowra | Safety Hire, Nowra | Safety Services, Nowra
Site by 8WEB