
A harness can look serviceable while hiding damage that will matter only when a worker falls. Knowing how to inspect safety harness equipment properly is not paperwork or a box-ticking exercise. It is a pre-start control that must happen before every use, by the person who will wear it.
A quick glance is not enough. Take the harness in your hands, check it in good light and follow a consistent sequence every time. If there is any doubt about its condition, remove it from service. A delayed job is manageable. A fall-arrest system that fails is not.
Start with the harness history and identification
Before inspecting the webbing, find the manufacturer’s label. It should be legible and securely attached, showing details such as the manufacturer, model, serial or batch number, manufacture date, applicable standard and inspection information. These details allow the harness to be tracked in the site register and assessed against the manufacturer’s instructions.
If the identification label is missing, unreadable or altered, do not make assumptions about the harness’s age, rating or inspection status. Tag it out and have it assessed by the person responsible for height-safety equipment. A harness without traceable identification cannot be properly managed.
Check that the harness is within its required formal inspection period. Pre-use inspections and scheduled competent-person inspections are different controls. Workers inspect before each use; a competent height-safety equipment inspector carries out and records the more detailed periodic inspection required by the manufacturer, site procedure and applicable Australian requirements.
How to inspect safety harness webbing
Lay the harness out flat or hold it by the dorsal D-ring and let the straps hang freely. This helps reveal twists, missing components and incorrect reassembly. Run every length of webbing slowly through your hands, front and back, including shoulder straps, chest strap, leg straps, sub-pelvic straps and any work-positioning sections.
Look and feel for cuts, tears, fraying, loose fibres, broken yarns, abrasion, thinning, heat damage and hard or glazed sections. Pay close attention to areas that run through buckles and adjusters, sit under tool belts, rub against edges, or contact scaffold components and ladders.
Discolouration can also be a warning. Paint, cement slurry, solvents, fuels, acids, welding spatter, battery chemicals and salt contamination can weaken fibres even where the damage is not immediately obvious. Excessively dirty webbing should not be treated as merely untidy. Dirt can conceal damage and some contaminants can degrade the material.
Check for unauthorised repairs. Knots in webbing, tape, cable ties, stitched repairs, drilled holes and improvised modifications are not acceptable. Do not try to repair a harness yourself unless the manufacturer has provided an authorised repair process and the work is completed by an approved person.
Inspect the stitching and load points
Stitching is a critical part of the harness structure. Examine all load-bearing stitch patterns around D-rings, buckles, chest straps, leg straps and attachment points. Look for loose, broken, pulled or worn threads, as well as heat damage and contamination.
The dorsal D-ring, normally positioned between the shoulder blades, is the primary fall-arrest attachment on most harnesses. Check that it is not bent, cracked, excessively worn, corroded or distorted. Also inspect any front, side or ventral attachment points fitted to the harness. Different attachment points have different intended uses. Do not connect a fall-arrest lanyard to a point unless the manufacturer specifically identifies it as suitable for fall arrest.
Check buckles, adjusters and hardware
Operate each buckle and adjustment device. They should engage positively, move as designed and hold the webbing securely once adjusted. Tongue buckles must have sound holes and tongues. Quick-connect buckles must click and lock fully. Friction buckles and adjusters must not slip or show sharp edges that could cut the webbing.
Inspect all metal hardware for cracks, distortion, sharp edges, pitting, rust, corrosion and excessive wear. Aluminium components can show white corrosion; steel components can rust, particularly in coastal, marine and wet-work environments. Salt air on the NSW South Coast, for example, can accelerate corrosion when equipment is poorly cleaned and stored.
Plastic components such as web keepers, buckle covers and retainers should also be intact. A broken keeper may seem minor, but it can allow excess strap to interfere with adjustment or snag during work.
Look for evidence of a fall or shock loading
Any harness involved in a fall arrest, suspected shock load or rescue must be removed from service immediately. The force generated in a fall can damage webbing, stitching and hardware in ways that cannot be confirmed by a visual check alone.
Some connected equipment, including energy-absorbing lanyards and inertia reels, have deployment or load indicators. Check these according to the manufacturer’s instructions. A deployed energy absorber, extended tear webbing, activated indicator or damaged connector means the item is not to be reused.
Do not return equipment to service because a worker says the fall was short, controlled or “not too bad”. The equipment needs formal assessment or disposal in line with the manufacturer’s requirements and workplace procedure.
Inspect the complete fall-arrest system
A harness is only one component of the system. Before starting work, inspect the compatible lanyard, energy absorber, self-retracting lifeline, connectors, anchor device and anchor point as well. Confirm that components are compatible and that connectors cannot be side-loaded, cross-loaded or accidentally disengaged.
Check the work area for sharp edges, leading-edge hazards, hot work, moving plant, electrical risks and obstructions below. Clearance matters. Even a correctly fitted harness cannot prevent injury if the worker strikes a lower level, scaffold, pipework or plant during a fall.
The system must also be used within its design limits. Worker mass, tool weight, lanyard length, anchor location and swing-fall exposure all affect whether the arrangement is suitable. If the site layout changes, reassess the system rather than assuming yesterday’s setup remains safe.
Fit the harness correctly after inspection
A harness that passes inspection still needs to fit properly. Put it on without twists. The dorsal D-ring should sit between the shoulder blades, chest strap should sit across the mid-chest, and leg straps should be snug without restricting movement or circulation.
Tighten and secure all adjustment straps, then stow excess webbing using the supplied keepers. Ask another trained worker or supervisor to check the fit where practical, particularly for new workers or complex harness configurations. A loose harness can increase injury risk during a fall, while an incorrectly adjusted chest strap may allow a worker to slip out.
Do not wear a harness over bulky clothing that prevents correct adjustment. If cold-weather gear, chemical suits, welding PPE or respiratory equipment is required, confirm that the complete PPE arrangement works together and does not obstruct attachment points or buckles.
Quarantine suspect equipment straight away
When a defect is found, stop using the harness. Tag it clearly as out of service, physically separate it from usable equipment and report it under your workplace procedure. Do not leave it in the harness rack for the next person to pick up.
A useful inspection record identifies the equipment type, manufacturer, serial number, inspection date, condition, defects found, action taken and inspector. Good records help employers identify repeat damage patterns, such as equipment being dragged across concrete, stored in damp vehicles or exposed to welding work.
Store serviceable harnesses clean, dry and away from direct sunlight, chemicals, sharp objects and heat sources. Throwing a harness in the back of a ute with chains, tools and fuel containers is a reliable way to shorten its service life.
Inspection does not replace a rescue plan
Pre-use inspection is one part of safe work at height. The job also requires suitable anchorage, trained workers, supervision, exclusion controls and a workable rescue plan. Under AS1891-2025 requirements, workplaces must not rely on emergency services as their rescue plan for a worker suspended after a fall. Rescue capability must be planned, available and suited to the site.
Workers and supervisors who need practical height-safety skills can complete RIIWHS204E Work safely at heights, delivered by Combined Safety Training on behalf of Allens Training Pty Ltd, RTO 90909. For teams undertaking height work in isolated, complex or high-risk locations, rescue training should match the equipment and conditions they will actually face.
Treat every pre-use inspection as a decision point. If the harness, the rest of the system or the rescue arrangements do not stack up, do not clip on and hope for the best. Stop, rectify the issue and only proceed when the fall-protection system is ready to do its job.
